+420 381 410 100 info@atal.cz
AT840 5004 Suspension Shock Absorber Testing Device - Mobile Version

Return menu

Back tu homepage  Back to overview of car diagnostics 

Car Diagnostics

AT840 Suspension Shock Absorber Testing Devices

Shock Absorber Testing Device

  • The suspension shock absorber testing device is used for inspecting the condition of shock absorbers of vehicles with maximum axle load of 2,500 kg

Unique Measuring Method

  • The testing device differs from current testing benches by analysing the response of the shock absorber based on resonance frequency (the most critical frequency for determining the vehicle’s adhesion to the road surface) instead of examining the minimum adhesion value of the wheel (EUSAMA method).
  • This method eliminates distortions during measurement caused, for instance, by incorrectly inflated tyres or improperly loaded vehicle.

    Simple Interpretation

    The measurement results are clearly explained to the user thanks to classification in three categories:

    • Good (green)
    • Worn (yellow)
    • Faulty (red)

    Report Printing

    • A complete test of a vehicle can be finished in only 3 minutes.
    • Allows printing a test report for the customer which explains in simple terms the condition of each shock absorber and asymmetry of axles.

    Testing device Parameters

    • Maximum axle load……………………………… 2,500 kg
    • Maximum testing frequency ………………………25 Hz
    • Minimum testing frequency ………….…………….3 Hz
    • Excitation width…………………………………… +/-3 mm
    • Engine power………………………………………2 x 2.2 kW
    • Minimum width………………………….…………..836 mm
    • Maximum width ……………………….…………..2096 mm
    • Testing device power supply……400 V 3-ph. – 50 Hz
    • Stand power supply ………………230 V 1-ph. – 50 Hz
    • Dimensions………………………3100 x 600 x 228 mm
    • 4 approach ramps ……………………….630 x 692 mm
    • Testing bench height ……….…………………..120 mm
    Example of reports from shock absorber testing device
    Shock absorber measurement result: GOOD (green)

    The shock absorber is

    FINE

    Shock absorber measurement result: DAMAGED (yellow)

    The shock absorber is

    WORN

    Shock absorber measurement result: POOR (red)

    The shock absorber is

    FAULTY

    Up-to-date overview of all available devices for shock testing.
    Clicking a button or a picture will show you additional info about the product

    více info o AT840 5004 mobilni tester tlumičů

    AT840 5004

    Mobile Shock Absorber Testing Device

    Equipped with a specifically modified trailer for mounting in the field.

    více info o AT840 5006 stacionárním testeru tlumičů

    AT840 5006

    Stationary Version (Surface-Mounted)

    Equipped with a mobile stand, PC and printer for use in the repair shop.

    více info o AT840 5007 vestavěný tester tlumičů

    AT840 5007

    Built-in Version

    Firmly built into the floor.

    více info o AT840 5001 tester tlumičů verze Modul

    AT840 5001

    Shock Absorber Testing device – Modular Version

    Not equipped with a stand or a PC. Can be connected to any PC or laptop..

    AT840 5004 Mobile Version (Trailer)

    • Equipped with a specifically modified trailer for mounting in the field.
    • Its simple installation takes at maximum 20 minutes for a single person.
    • Revolutionary low-profile adjustable measuring bench for carrying the axle of the vehicle for testing.
    • Installation of the device is very simple and requires no special investment.
    Open brochure (pdf)
    AT840 5004 Mobile Shock Absorber Testing Device

    AT840 5006 Stationary Version (Surface-Mounted)

    • Type equipped with a mobile stand for mounting onto a flat surface
    • The mobile stand contains: industrial PC box, 19“ LCD screen, keyboard, mouse, printer
    • Revolutionary low-profile (12 cm) adjustable measuring bench for carrying the axle of the vehicle for testing
    • Installation of the device is very simple and requires no special investment (structural modifications).
    • Suitable for installation into finished areas.
    Open brochure (pdf)
    AT840 5006 Suspension Shock Absorber Testing device - Stationary Version

    AT840 5007 Built-in Version (for Inspection Pits)

    • The measuring bench is built into the pit.
    • Construction modifications needed for installing the testing device must be arranged for by the customer.
    • The mobile stand contains: industrial PC box, 19“ LCD screen, keyboard, mouse, printer.
    Open brochure (pdf)
    AT840 5007 Built-in Shock Absorber Testing Device

    Modular Version

    • Not equipped with a stand or a PC
    • Can be connected to any PC or laptop
    Open brochure (pdf)
    AT840 5001 Shock Absorber Testing device - Modular Version

    For more information, prices and terms of delivery, contact the sales department, agenda SHOCK ABSORBERS

    Last page update: January 14, 2019